48 THE DISTRIBUTOR’S LINK When installing Coiled Spring Pins, it is important that the installation tool, often called a “quill”, is large enough to cover the entire end of the Coiled Pin. The quill should be sized such that it pushes on all five coils simultaneously throughout the entire installation process. Otherwise, the pin will be difficult – if not impossible – to properly install into the assembly. If the quill is too small, the inner coils will push through the center of the pin creating a “telescoping” effect and push out the back end of the Coiled Pin. Sometimes, users refer to this as the pin “unwrapping”. It is important to note that it is impossible for pins to “telescope” or “unwrap” if the proper insertion quill is used. A byproduct of pushing on the inner coils is elevated insertion forces, and if the quill is too small, the Coiled Pin will not be able to flex to take on the diameter of the hole since the quill will be lodged in the ID of the pin. Occasionally, a company will develop an insertion quill that has a stepped end that is intended to fit into the ID of the Coiled Pin to “help align the pin with the hole” (Figure 1). There are two problems with this scenario. The first problem is that the actual center of the Coiled Pin is Spirol International Corporation 30 Rock Avenue, Danielson, CT 06239 Tel: 1-860-774-8571 Fax:. 1-860-774-2048 Email: info@spirol.com www.spirol.com THE IMPORTANCE OF THE INSERTION QUILL WHEN INSTALLING COILED SPRING PINS by Christie L. Jones, Market Development Manager LEFT: Figure 1: An insertion quill with a stepped end, as shown, is not recommeded. RIGHT: Figure 2: Black crosshairs show the center of the coiled pin’s inner diameter. Red crosshairs show the actual center of the coiled pin. The quill should be sized such that it pushes on all five coils simultaneously throughout the entire installation process. not in the center of the ID (Figure 2). Therefore, the effect of sticking something into the ID of the pin is that it will actually knock the pin off-center from the hole! The second problem is that the nib at the end of the installation tool may prevent the pin from collapsing as it is inserted into the hole. This can significantly raise insertion forces; and if the nib is large enough, prevent full insertion of the pin into the hole. In some cases, the quill can break off and get stuck in the ID of the pin causing downtime on the assembly line. Another common issue is when a company continues to use a worn insertion quill. Over time, the end of the insertion quill will break down. Notice on Figure 3 the tip of the tool, circled in red, is worn and the edges are smoothed over. At some point, the end of the quill will be too Figure 3: Worn insertion quill. small such that it will not cover the entire end of the Coiled Pin. As described above, the quill will press on the inner coils of the pin, and insertion issues will arise. please turn to page 183
98 THE DISTRIBUTOR’S LINK FASTENE
102 THE DISTRIBUTOR’S LINK Arnold
106 THE DISTRIBUTOR’S LINK by Del
THE DISTRIBUTOR’S LINK 109 UNIQUE
NATIONAL INDUSTRIAL FASTENER & MILL
THE DISTRIBUTOR’S LINK 115 MID-WE
118 THE DISTRIBUTOR’S LINK NEFDA
120 THE DISTRIBUTOR’S LINK Elgin
124 THE DISTRIBUTOR’S LINK PWFA -
128 THE DISTRIBUTOR’S LINK New fr
THE DISTRIBUTOR’S LINK 135 As man
BRIGHTON-BEST INTERNATIONAL COCKTAI
142 THE DISTRIBUTOR’S LINK ULTRA-
Edwards & West Inc., t/a Divspec ha
THE DISTRIBUTOR’S LINK 151 Rapid
156 THE DISTRIBUTOR’S LINK THE BU
160 THE DISTRIBUTOR’S LINK BOLT M
164 THE DISTRIBUTOR’S LINK TAKE A
THE DISTRIBUTOR’S LINK 167 ACCURA
more photos on page 180
174 THE DISTRIBUTOR’S LINK GAMECH
176 THE DISTRIBUTOR’S LINK NCFA -
178 THE DISTRIBUTOR’S LINK AN UPD
PAC-WEST 2012 FALL CONFERENCE SCOTT
182 THE DISTRIBUTOR’S LINK AN UPD
184 THE DISTRIBUTOR’S LINK SEFA -
186 THE DISTRIBUTOR’S LINK CADMIU
THE DISTRIBUTOR’S LINK 189
THE DISTRIBUTOR’S LINK 191 J.W. W
THE DISTRIBUTOR’S LINK 193 FAN DI
MFDA TABLETOP SHOW THE FIESTA, NEW
THE DISTRIBUTOR’S LINK 197 MFDA T
THE DISTRIBUTOR’S LINK 199 MFDA G
PAC-WEST 2012 FALL CONFERENCE SCOTT
THE DISTRIBUTOR’S LINK 203 Whitfo
THE DISTRIBUTOR’S LINK 205 PAC-WE
208 THE DISTRIBUTOR’S LINK
212 THE DISTRIBUTOR’S LINK D cont
216 THE DISTRIBUTOR’S LINK S cont
Loading...
Loading...
Loading...
SHARE A PAGE FROM THIS MAGAZINE OPTION 1: Click on the share tab above, or OPTION 2: Click on the icon (far right of toolbar) and then click on the icon (top right of the page). |
Copyright © Distributor's Link, Inc. All Rights Reserved | Privacy Policy